Dixie Narco 501E & 600E SODA Vending Machine CAN Shim KIT OEM /!

Dixie Narco 501E & 600E SODA Vending Machine CAN Shim KIT OEM /!

Snack Attack Vending LLC is offering a CAN Shim Kit for Dixe Narco soda machine models 501E & 600E. The set consist of (8) single column metal shims & (8) double column plastic shims (4 shims on each side). This Can Shim Set is brand new from factory. No rotor rods needed to vend cans! Single Column Instructions: Power down machine before installing shims. Start by adjusting the single brown vend motor cam discs. Lightly pull disc tab towards you and turn disc clockwise to #1 hole snaps in. You should have 3 notches on disc for 3 deep cans. Then Adjust double wide column red/grey disc to #2 hole snaps in. You should have 6 notches around disc for 3 deep cans. Take springs off “sold out” flappers above vend motor. Power machine up and pull out white door button located between coin mech & bill validator. This will reset vend motor cams. Now vend each single column brown vend motor so that the rotor cup is in the right, 3:00 o’clock position . This will allow you an inch gap to take out metal bottle shims and replace with can shims. The metal can shim rests on a metal rod front of machine and rear. Double column Instructions: Take out double column plastic bottle shims and replace with plastic can shims 4 on each side with dog leg thicker part to rear. Adjust vend motor red / grey cam to position #2 for 6 notches in disc. Attach “sold out” springs and load machine to test vend & prime down cans till they vend out.

It sounds like you’re looking for a Dixie Narco 501E & 600E Soda Vending Machine Can Shim Kit (OEM). This kit is typically used to adjust the vending mechanism so that it can properly vend cans of different sizes or to accommodate slight variations in the size of the cans. The Dixie Narco 501E and 600E are models of soda vending machines that were quite popular, and the shim kit helps to ensure smooth operation and reliable dispensing of cans.

Here’s a bit more about the two models:

1. Dixie Narco 501E:
   • A single column soda machine that typically holds 5 selections and is designed to vend 12 oz cans.
   • It is commonly used in small locations like office break rooms, convenience stores, or schools.
2. Dixie Narco 600E:
   • A larger capacity version, often featuring more selections and can handle up to 600 cans, depending on the configuration.
   • Typically used in higher-traffic areas like malls, large office buildings, or public spaces.

Can Shim Kit for soda vending machine

A can shim kit (OEM part) typically includes various shims designed to adjust the width of the can selection mechanism inside the machine. These shims help to ensure that different sizes of cans can be vended smoothly. Over time, vending machines can experience wear, or you may need to adjust the width to accommodate different brands or types of cans.

What to Look For: in this soda vending machine

• OEM (Original Equipment Manufacturer) parts are usually preferred for their compatibility and quality.
• The shim kit should include shims that fit your specific machine (501E or 600E). If you’re unsure, verify the model and serial number of your vending machine to ensure compatibility.

If you’re looking to purchase the kit, you can check the following sources:

• Vending machine part suppliers: Websites like Vending World, A&M Equipment Sales, or Vending Parts often carry OEM parts.
• eBay or Amazon: These platforms sometimes have vending machine parts, including shim kits.
• Direct from Dixie Narco or authorized dealers**: You can often order OEM parts directly from the manufacturer or their authorized dealers.

If you need specific instructions on how to install the shim kit or troubleshooting advice for your vending machine, I can help with that too.

Dixie Narco 501E & 600E SODA Vending Machine CAN Shim KIT OEM /!